Service Line

Model P16HP P16AP P20HP P20AP P20CS P32CS
Crimping range (mm) 1 10 — 45 10 — 45 10 — 61 10 — 61 10 — 61 10 — 87
Crimping range (inches) 1 0.39 — 1.77 0.39 — 1.77 0.39 — 2.40 0.39 — 2.40 0.39 — 2.40 0.39 — 3.42
Crimping force (kN) 955 955 1370 1370 1370 2000
Crimping force (tonnage) 95 95 137 137 137 200
Crimpings / hour 2 — — — — 250 150
Max. hose size (inches) 1 1 1½ 1½ 1½ 2
Die set 3 kysymysmerkki
 P16 P16 P20 P20 P20 P32
Maximum opening (mm) 4 +20 +20 +25 +25 +25 +33
Master die (D / L mm) 39 / 64 39 / 64 84 / 80 84 / 80 84 / 80 99 / 80
Master die (D / L inches) 1.54 / 2.52 1.54 / 2.52 3.31 / 3.15 3.31 / 3.15 3.31 / 3.15 3.90 / 3.15
Control kysymysmerkki manual manual manual manual MS MS
Motor (kW) hand pump air pressure hand pump air pressure 1.6 / 2.2 5 1.6 / 2.2 5
Motor (HP) hand pump air pressure hand pump air pressure 2.1 / 3.0 5 2.1 / 3.0 5
QC tool 14 kysymysmerkki — — O O O O
Foot pedal 15 kysymysmerkki — — — — — —
Control unit: integrated kysymysmerkki X X X X X X
Control unit: C1 kysymysmerkki — — — — — —
Control unit: C2 kysymysmerkki — — — — — —
Back stop device: mechanic kysymysmerkki — — O O O O
Back stop device: electric 15 kysymysmerkki — — — — — —
Mirror kysymysmerkki — — — — — —
UC1 — — — — — —
UC2 — — — — — —
UC3 — — — — — —
Auto greasing G3 16 kysymysmerkki — — — — — —
Remotic control unit kysymysmerkki — — — — — —
Counter — — — — — —
ASCII signal — — — — — —
Length (mm) 331 331 487 571 571 626
Width (mm) 401 346 441 477 533 543
Height (mm) 271 271 389 345 387 421
Length (inches) 13.1 13.1 19.2 22.3 22.3 24.9
Width (inches) 15.7 13.6 17.4 18.8 20.6 21.5
Height (inches) 10.7 10.7 15.4 13.4 15.2 16.8
Weight (kg) 26 28 66 59 83 116
Weight (lbs) 57 62 146 130 183 256

 

X = standard
O = optional
— = not available

  1. With standard dies. Crimping range can be increased with special dies.
  2. Theoretical with ½ hose, diameter 10 mm.
  3. See table for die set data.
  4. Maximum opening is the total die travel. Add this value to the minimum crimping diameter of the die set used. The result is the maximum opening of the machine with die set in place.
  5. 12V / 24V. Overload controlled.
  6. 1-phase / 3-phase.
  7. FP140 dies can be used without adapter dies.
  8. Hydraulic hose / industrial hose.
  9. With adapter dies.
  10. Hose cutter.
  11. Full cycle.
  12. Die travel / feeding channel.
  13. NC20, NC30 and NC40 dies can be used.
  14. Available for P20, P32 and CC22 dies.
  15. Not available in MS control.
  16. Technical implementation varies depending on the machine model. Please verify the suitability of the option from your distributor.
  17. Available in UC models only.
  18. Standard feature in UC models, includes ascending/descending counter.

 

18212 P16 18013 P20  18506 P32
Mainostoimisto BSTR Luova Konttori Seinäjoki ja Vaasa